A click of a photograph looks at Catalog PDF.

TM-5000 ■FEATURES 　 　● HIGHLY EFFICIENT DRIVER'S AID SYSTEM for 　　　both DEVELOPMENT AND TESTER LINE 　● Easy interface with Existing Automotive 　　　Measurement Systems 　● Use both Analog or Pulse Train input to measure 　　　Vehicle Speed 　● MONITORING OF ANALOG MEASUREMENT 　● Use both Color CRT Monitor and Color TFT LCD 　　　of commercial XGA correspondence 　● Selectable Pendant (Portable, Wired, Wireless） 　● Visual and Audible Driver Prompts highlight each 　　　Shift Point 　● Custom Driving Patterns Easily Programme 　　　by User ■Driver's Aid　ＴＭ−５０００ 　 Color Display：Choose any of the following: A conventional CRT of flat panel TFT LCD. All use XGA compatible, 1024×768 pixels, with Analog RGB interface. Hand-held Pendant：Choose any of the following: Wired or Wireless or Portable. Speed Analog input：200km/h maximum full scale display. Switch selectable Analog input Ranges from 0.5V to 50V DC F.S. in a 1-2-5 sequence. Zero and Full scale points are adjusted automatically. Output：Analog: Select any four (4) parameters as an output. e.g., Actual Speed, Scheduled Speed, etc. Full scale output=10V DC. Storage Media：Hard Disk 10GB. All of these storage media can be installed in the same unit. Standard Interfaces：Keyboard (date input), Mouse (setup), LAN (computer) Power Supply：AC100V 160VA 50/60Hz Environment：0〜40℃，20〜80%RH Dimensions：W414×H131×D453mm Mass：12.5kg ■Pressure Gauge　ＰＧ−４／ＰＧ−２１／ＰＧ−４０ Model ＰＧ−　４−００ ＰＧ−２１−００ ＰＧ−４０−００ Function Pressure measurement Input method φ4.5mm(The rubber pipe of 3mm of the diumeters of inner for connection) Number of input １ｃｈ ２ｃｈ ４ｃｈ Measuring range -100kpa 〜 　+300kpa 15kg/c�u 　0 〜 ±100kpa -100kpa 〜 　+200kpa 4ch all Display signal +3digit signal +4digit signal +4digit Analog output -1V 〜 3V 0〜1V， 0〜±1V -1V 〜 2V Accuracy ±0.5% / FS ±0.3% / FS ±0.25% / FS ±0.25% / FS Response speed 10Hz(-3dB) Dimensions W165×H65 ×D200mm W250×H100 ×D250mm W300×H100 ×D250mm Mass Approx.1kg Approx. 3kg Approx. 4kg Power supply AC90〜132V 　　　　−　　 DC9 〜 16V 5VA max 10VA max 10VA max ■Engine revolution measurement　ＲＥＶ−５１０ 　 Measuring range：300rpm〜10000rpm Accuracy：Digital ±1rpm+1digit Resolution：1rpm(FX2) (case 6μs of FX-13) Response speed：One measurement in 2 revolutions Input pulse setting：Copes with 0.1P/R〜99.9P/R 　　　　※ set the pulse rate to 1P/R when measuring mark sensor 　　　　　　 ECU revolution pulse output. Setting of data transfer average：Performs data moving average, Number of data : 40 Analog output：0〜1V=0〜10000rpm 　　　　　　　　　　　　　0〜10V=0〜10000rpm 2ranges Digital output：Engine revolution pulse signal 　　　　　　　　　　 Engine ON status signal 　　　　　　　　　　 Engine over speed (emergency stop) status signal Revolution pulse output：1 revolution 1 pulse signal Engine revolutions：5figures 0〜10000rpm Power supply：AC90〜132V Power consumptions：50VA max Operating temperature and humidity range：0〜40℃，30〜80%RH(no condensation) Dimensions：W220×H75×D350mm Mass：5kg ■Thermometer　ＴＣ−８，ＴＣ−１６ 　 Channels/Width：TC-8：8ch，TC-16：16ch Thermo couple：J，K，T Measurement Range：J：-200℃〜1200℃ 　　　　　　　　　　　　 　　　K：-250℃〜1300℃ 　　　　　　　　　　　　 　　　T：-250℃〜400℃ Response speed：DC〜　approx.5Hz (+0.5dB，-3dB) Display：minimum beam 0.1℃ Output Voltage：1mV/1℃ Power supply：AC90〜132V Dimensions：TC-8 ：W320×H100×D320mm 　　　　　　　　 ：TC-16：W320×H190×D300mm Mass：TC-8：約5kg，TC-16：約8kg